Author Archives: mahbooba

Egg Incubator Turning Tray Trigger Time Delay Seting

Category : Technical

6-30V 1 Channel Relay Module Switch Trigger Time Delay Circuit Timer Cycle Adjustable

Features of Timer relay for incubator:

1. Trigger Signal Source: High Level Trigger (3.0 V-24 V), signal ground and system ground are not common, which can increase anti-interference abilit

system (short circuit can also connect with a ground common)

2. Output Capacity: can control no more than DC 30V 5A AC or 220 V devices 5A

3. Optocoupler Isolation: improve the anti-interference ability, after the parameter setting, it will memory forever timer relay Switch


Material: Electrical components

Color: See pictures

Size: 6.3×3.8×1.5cm

Operating voltage: 6-30V timer relay

Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustable

Operation Mode:

P1: After triggered signal, power relay on time OP, then turn off; within the OP period following operation timer relay Switch

1) P1.1: Signal being triggered again is not effective

2) P1.2: Signal being triggered again, start time again

3) P1.3: Signal being triggered again, reset; disconnect relay, stop timing

P2: Giving the trigger signal, the time after shutdown relay CL power relay OP time; then timing, turn off the relay

P3.1: Give the trigger signal after the power relay on time OP, CL shutdown time relay; then operating cycle above cycle gaive signal again, shutdown relay stop timing; cycle times (LOP) can be set timer relay

P3.2: After connecting. no need to trigger signal, power relay on time OP, CL shutdown time relay; then the operating cycle above timea cycle (LOP) can be set

Q4: Keeping the function of the signal; if there is no trigger signal, the time will be canceled, relay stay connected; when the signal disappears, timing OP turn off the relay; over time, if no signal again, the time is cleared

how to choose the time interval:

timer relay Switch

parameter Introduction: OP power over time, turn off time CL, LOP cycle times (1-999 times, “—” is unlimited cycle)

1. In the selection of parameter set interface mode, and press the STOP button to select the time.

(1)xxx. if the decimal point is in some place, the time interval is s-1 999 s

(2)xx. x is decimal place is ten, the time interval is 0.1 s 99.9 s-

(3)x. x. x is the decimal point are all on, the time interval is 1 min-999 min

How to set the parameter:

timer relay Switch

1. First make sure relay operation mode

2. According to the operaiting relay mode, the main interface (power module will flash current operating mode; standard mode P1.1, then come intot main interface); long press SET key two seconds and then looen enter selection interface mode; by pressing UP, DOWN key to choose the mode setting

(P1.1 ~ P4)

3. After selecting the mode, press short SET to set the corresponding parameter, then the parameter you want to set will flash

(OP power in time; CL power off time; LOP cycle times, “—” is unlimited cycle ); by UP, DOWN to set the parameter value, support long press

(increase or decrease quickly) and press slightly (increase or decrease of 1 unit); after setting the parameter value by short press the STOP key to choose decimal place; choose the time interval (corresponding time interval is 0.1 s-999 min); Short press SET to set the current mode next parameter, the process is the same as above

4. After the setting mode parameter, press and hold the SET button then hold the current configuration mode will flash, then go back to the main interface; define success parameter

main interface: when the relay does not work, it will show “000” (no decimal point); the operating state relay, the screen has a decimal point

Mode Select Interface:

press and hold the SET key to enter; after setting, long press the SET button back on main interface 6-30V 1 Channel RELAY

Activate Relay Mode Timer relay for incubator:

1. NO: PO in power over time, relay can be connected

2. OFF: relay is not allowed to connect, when in the off state

in short main interface press the STOP key to achieve turn ON and OFF, current state will flash; then back to the main interface 6-30V 1 Channel RELAY

(this function is a function of sudden stop, 1 key to turn off the relay)

Sleep Mode:

C-P Sleep mode: within 5 minutes, no operation; nixie tube will close auto display, and a function program well e

Automatic Egg Incubator & Hatching System

Category : Technical

Fully Automatic Birds Egg Incubator
With Roller Tray all kinds of bird egg, Easy to use Efficient Rely Control, Low Power Consumption due to wall temperature control technology,
Accept order online All Pakistan Delivery
Lowest price according to market Price with After sale Technical support

“Mahboob Mechanize” designee & manufacture a low cost and economical birds egg incubator for home and cottage industry use we try to make a best product using advance technology.

Qualities of Our Products:

Very low electricity consumption due to temperature control wall , Efficient and easy to use rely control temperature, humidity and egg rotation system also operate on battery or solar panel, Lowest price of Product as compare to market price over all Pakistan


Category : Technical

Dual T.E.N.S, Electronic Physiotherapy, Electronic Acupuncture

Key Features: ·         Easy and simple physiotherapy at your own convenience. ·         Best for doctor, physiotherapist or home use. ·         A safe and useful alternative to medicines. ·         No medical recommendation required. ·         No side effect, no reaction. ·         Quick results. ·         Heavy duty construction. ·         Large size, long life silicone electrodes with gel.

  • One device many applications!

Advantages of ET1: (Electrotherapy / T.E.N.S. Unit) ·          Fast effective and safe pain reliever, just like this CBD cream that reduces pain. Improves body’s own immune system to fight ailments and diseases. ·          Provides a massage course. ·          Recovers from fatigue. ·          It is an electronic acupuncture device (acupuncture without needles). ·          Provides electronic physiotherapy. ·          Can be used with ease and simplicity. ·          Two separated outputs for two body parts, or two persons. ·          Does not require expensive batteries. ·          No electric risk due to the use of two isolated transformers. ·          Pulses with rectangular “balanced” waveform with zero net DC components. ·          Wide-range of Frequencies / Pulse.

  • Large, electrode pads for gentle massage.

How it Works? In use, two or more electrodes are placed on the skin surface, usually above or on either side. A small, pulsed current is passed between them. To place electrodes properly, user refers to the detailed charts and tables given in the user’s manual. A fairly high voltage is required to pass the current (off course it is tiny and safe) through the body. By providing a pleasant electronic stimulus to nerve tissues, cells and blood vessels, it causes contracting movement of organs, thus contributing greatly to removing various elements impeding circulation of blood, such as cholesterol and effete matters attached to peripheral blood vessels.   Some applications:

It gives a stimulus to the autonomic nervous system as well as lets the paralyzed muscle contract, calm down excited nerves to remove pain and relieve fatigue, thus harmonizing various functions of the body by quickening secretion of hormone and enzyme necessary to maintain the human body.
In many cases this produces significant relief, and it has been known to succeed where all other means have failed.

Effectiveness for Pain Treatment: Do you feel pain getting out of bed? Or walking up the stairs your ET1 Electrotherapy / T.E.N.S. can help you.   T.E.N.S. (Transcutaneous Electrical Nerve Stimulation) is a modern, non invasive, drug free, pain management commonly used for short term acute pain or long term chronic pain.   Pain is the body’s defense mechanism telling you something is wrong, but it is debilitating and annoying. ET1 T.E.N.S. helps the body get out of pain.   A T.E.N.S. Unit is great for a variety of injuries, back pain, neck pain, shoulder pain, knee joint pain, and muscle associated pain as well as many other work and sport related injuries, such as: carpal tunnel syndrome, RSI (Repetitive strain injuries) and many other problems related to today’s sedentary working environments.   It is highly effective on all form of rheumatoid arthritis, congestion, soreness, muscle strains and sport injuries as it relieves pain, reduces inflammation, and relaxes affected areas. Use to assist treatment of headache, toothache, tennis elbow. Relieves soreness in the applied area and much more!  

It also enables you to enjoy the benefits of rapid healing of injury and the ability to rehabilitate. 

What Diseases it Cures?

This device can be used to treat a wide variety of diseases and common ailments, including:   Appetite loss, Beauty massage, Blood circulation problems, Body building / Muscle exercise, Cystitis, Decline in energy, Diabetes, Diarrhea, Enuresis, Eye strain, Fever / High temperature, Foot massage (Anti-aging therapy), Gastric ulcer, Gastritis, Headache, Hemorrhoids (Piles), High blood pressure, Indigestion, Insomnia, Knee joint inflammation, Leucorrhea, Lumbago, Menstrual irregularity / Gynecologic condition, Muscle pain (Legs), Muscle pain (Arms), Nervous system imbalance, Nervous tension, Neuralgia, Over weight / Extra fat removal, Pain, Arthritis pain, Back pain, Neck pain, Shoulder pain, Palsy, Paralysis, Facial neuralgia, Facial paralysis, Peptic ulcer, Rheumatism, Sciatic nerve (Sciatica), Sexual vigor improvement, Spinal impulses, Spinal imbalances, Tiredness / Weariness, Tooth ache, Ulcus cramp,  

It also enhances natural healing power and causes favorable turn in various symptoms.

Other Features:

Strengthens muscles: Helps to strengthen and tone musclesat your convenience.  

For Weight Reduction and Beauty Massage:

It purges toxins and helps in weight loss when it is used on your waist, arms, legs etc. The electric conduction of the electrodes is safe and comfortable.   For Infertility, Impotence or Lack of Sexual Desire: ET1 promotes peripheral blood circulation in the effected region (due to daily stress or growing age) of the male or female body and enhances the activity to a normal balanced condition.   User Friendly Functions & Design: Unit has simply two control settings Pulse Duration and Amplitude Control. High Pulse stimulation: Relieving symptoms of chronic pain, stiffness & numbness. Low Pulse stimulation: Effective for acute pain and immediate blockage of pain transmissions. Intensity settings using comfort level dial (0 – 10 level selection).   Side Effects:  It has no side effect.   Safety: It has no electric risk due to the use of two isolated transformers and due to breakthrough technology of electrode pads.

12 Volt DC Air Cooler

Category : Technical

A room cooler convert in to 12 V DC solar or battery

My You Tube Chanel Click Here

Detail of Solar Power Click Here

A room cooler of 220 volt can easy to convert in to a 12 volt DC room cooler.

Two main changes required a motor and water pump normal air cooler use 220 volt 150 watt electric motor and water pump also both are consume electric power cause of high electricity bill.

If just two things replace in to 12 volt DC highly reduce of electricity bill almost free of coast if you use solar panel

Here is some example DC motor picture below as my experience to use to replace in AC to DC room cooler fig-1 high performance and low consumption with big size of fan blades this motor is easy available in local market

DC Motor in fig-2 also a best quality and high performance DC motor for best use with light wight fan blades also easy available in local market in lowest price range Rs. 150/- to Rs. 250/-

Water Pump in fig-3 most commonly use in fish aquarium and available AC 220 Volts and 12 Volts but here is we use 12 Volts as my personal experience is best choice for 12V room cooler mention below motor provide up to 200L water flow for the best of Air Cooler Cooling pads

DC Motor for room cooler

Fan Blade for DC Room Cooler in picture below Quality and size for cooler or normal use fan. blades avail in thousand of qualities and size in local market this kind of blades price depended as per size and quality. Easy fitting on all type of motors.

Available fan blades in local market

All above parts assembly/converting detail videos watch on my You Tub Chanel

very soon if any one need to assistance fell free to contact me

Wido small Drill press

Category : Technical

Wido small Drill press Model: WD030520013

Model No. WD030520013

Rated voltage: 220-240V~50Hz

Power input: 350 Watt

Volt: 220 V

No load speed: 580-2650/min

Chuck capacity: 1-13mm

Carton size: 365x235x475mm (CBM: 0.041m³)

Net/Gross weight: 15.4/ 16.4 kg

Last Purchase Price: ₨ 11,500/- Lahore Market Month of January 2020

Video Review on my You Tube Chanel Click Here

Digital Clamp Meter UNI-T

Category : Technical

Digital Clamp Meter Model: UT203

Digital Clamp Meter Model: UT203 in my personal use I am recommended for personal or home use best and watch video review on YouTube click here


DC Voltage: 400mV / 4V / 40V / 400V / 600V and Best accuracy: +/- (0.8%+1)

AC Voltage: 4V / 40V / 400V / 600V and best accuracy: +/- (1%+5)

DC Current: 40A / 400A – best accuracy: +/- (2%+3)

AC Current: 40A / 400A – best accuracy: +/- (2.5%+5)

Resistance: 400 Ohm / 4 kOhm / 40 kOhm / 400 kOhm / 4 MOhm / 40 MOhm -best accuracy: +/- (1%+2)

Frequency: 10Hz – 1MHz – best accuracy: +/- (0.1%+3)

Duty cycle: 0.1% ~ 99.9%

SPECIAL FUNCTIONS: Auto ranging Diode Continuity buzzer Relative mode Data hold Full icon display Sleep mode Low battery display

Input impedance for DC Voltage: 10 MOhm max.

Display 3999 (35.6 x 18mm)


Product size: 210 x 75.6 x 30mm Product weight: 200g

Manufacturer: UNI-TREND

So; final I have buy this.

I am use for my other solar equipment you can visit here

Belt & Disc Sander

Category : Technical

Look Belt & Disc Sander Model: P804503

An over look of Belt & Disc Sander video on my YouTube Click Here

Light weight  belt and disc sander combination flaunts a 1.5”x36” sanding belt, 6” sanding disc, A belt with 0° -90° tilt including a work support, a disc work table with 0° – 45° tilt, a heavy duty miter gauge, and a dust port

Features: Cast aluminum table that provides exceptional work support and tilts up to 45 degrees, precision tracking system, a safety key switch, and a quick release belt change; sturdy cast iron base and mounting hole prevent wobbling and walking

2in1 Design: sanding machine is equipped with both, an abrasive Belt and disc Combo, large enough and perfectly sized to handle an assortment of sanding and woodworking applications

Power: 220 Volt

I am With Subject Machine

My 300 Watt Solar System

Category : Technical

I have Installed 300 Watt 12 Volt Solar system watch video on You Tube Click Here

Use DC Room Cooler click here

Home Weather Station

Category : General Issue



Local forecast, highs/lows, totals or averages and graphs for virtually all weather variables over the past 24/7, months or years.

A customizable station with a wide range of options and sensors to help professionals and hobbyists measure, monitor, and manage weather data.

Stations are engineered to withstand scorching sun, corrosion, 200 mph (321 kmh) winds, temperature extremes, and more.

the highest level of accuracy, reliability and ruggedness.

All Vantage Pro-2 stations include a console and a versatile sensor suite that can be customized by adding consoles or special-purpose options.

Home Weather Station BENEFITS

– Inside Temperature and Humidity
– Outside Temperature and Humidity
– Barometric Pressure
– Dew Point
– Rainfall
– Detachable Wind Speed and Direction sensors
– Optional UV and Solar radiation sensors
– Optional additional temperature and humidity sensors

Update on YouTube

What Is a Lathe?

Category : Technical

In the manufacturing industry, the term machine tool gener­ally applies to a machine that cuts material either by the movement of a cutting tool into a fixed workpiece or by the movement of the workpiece past a fixed tool. All metal- cutting machines fit this description. In the case of the lathe, a fixed tool machines a rotating workpiece. Although the workpiece can be metal, plastic, wood, or most other solid materials, this study unit focuses on metal.

As noted above, a lathe is a machine tool that machines material by moving a fixed tool across a rotating workpiece. Figure 1 illustrates an example of a modern lathe. Modern lathes rotate workpieces using some type of electric motor, with the tool being moved manually, mechanically at a fixed feed rate, or electronically in the case of CNC lathes. Lathes can produce a variety of turned parts. With the proper attachments, lathes can produce many parts that would otherwise require a specialized machine.

Historically, the lathe has been considered the “king of the machine tools” because it had a greater capacity for work than any other type of machine tool. However, with the advances of CNC machinery, many features once machined only on the lathe an now be machined efficiently on a CNC machining center as well.

Watch Video Lecture on You Tube Click Here